Tolerance on ℓ
Unit : mm| ℓ Division ofℓ> |
Tolerance |
|---|---|
| 3 | ±0.2 |
| 3＜ℓ 10 | ±0.3 |
| 10＜ℓ 30 | ±0.4 |
| 30＜ℓ 50 | ±0.5 |
| 50＜ | ±0.6 |
특성표
Unit : mm| Nom Size d |
P | S | t | Screw End | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Pitch | min | Cup point | Flat point | Full Dog point | Cone point |
|||||||||||||
| dz | dp | dp | r1 | 3)Z \Short\dog point |
4) Long dog point |
dt | ||||||||||||
| 최대 | 최소 | 1)1 | 2)2 | 최대 | 최소 | 최대 | 최소 | 최대 | 최소 | app rox | 최대 | 최소 | 최대 | 최소 | 최대 | |||
| M1.6 | 0.35 | 0.7 | 0.724 | 0.711 | 0.7 | 1.5 | 0.8 | 0.55 | 0.8 | 0.55 | 0.8 | 0.55 | 0.1 | 0.65 | 0.4 | 1.05 | 0.8 | 0.16 |
| 2 | 0.4 | 0.9 | 0.902 | 0.889 | 0.8 | 1.7 | 1.0 | 0.75 | 1.0 | 0.75 | 1.0 | 0.75 | 0.1 | 0.75 | 0.5 | 1.25 | 1.0 | 0.2 |
| 2.5 | 0.45 | 1.3 | 1.295 | 1.27 | 1.2 | 2.0 | 1.2 | 0.95 | 1.5 | 1.25 | 1.5 | 1.25 | 0.2 | 0.88 | 0.63 | 1.5 | 1.25 | 0.25 |
| (2.6) | 0.45 | 1.3 | 1.295 | 1.27 | 2.0 | (1.3) | (1.6) | 1.5 | 1.4 | 0.2 | (1.5) | (0.25) | ||||||
| 3 | 0.5 | 1.5 | 1.545 | 1.52 | 1.2 | 2.0 | 1.4 | 1.15 | 2.0 | 1.75 | 2.0 | 1.75 | 0.3 | 1.0 | 0.75 | 1.75 | 1.5 | 0.3 |
| 4 | 0.7 | 2 | 2.045 | 2.02 | 1.5 | 2.5 | 2.0 | 1.75 | 2.5 | 2.25 | 2.5 | 2.25 | 0.3 | 1.25 | 1.0 | 2.25 | 2.0 | 0.4 |
| 5 | 0.8 | 2.5 | 2.56 | 2.52 | 2.0 | 3.0 | 2.5 | 2.25 | 3.5 | 3.2 | 3.5 | 3.2 | 0.3 | 1.5 | 1.25 | 2.75 | 2.5 | 0.5 |
| 6 | 1.0 | 3 | 3.08 | 3.02 | 2.0 | 3.5 | 3.0 | 2.75 | 4.0 | 3.7 | 4.0 | 3.7 | 0.4 | 1.75 | 1.5 | 3.25 | 3.0 | 1.5 |
| 8 | 1.25 | 4 | 4.095 | 4.02 | 3.0 | 5.0 | 5.0 | 4.7 | 5.5 | 5.2 | 5.5 | 5.2 | 0.4 | 2.25 | 2.0 | 4.3 | 4.0 | 2.0 |
| 10 | 1.5 | 5 | 5.095 | 5.02 | 4.0 | 6.0 | 6.0 | 5.7 | 7.0 | 6.64 | 7.0 | 6.64 | 0.5 | 2.75 | 2.5 | 5.3 | 5.0 | 2.5 |
| 12 | 1.75 | 6 | 6.095 | 6.02 | 4.8 | 8.0 | 8.0 | 7.64 | 8.5 | 8.14 | 8.5 | 8.14 | 0.6 | 3.25 | 3.0 | 6.3 | 6.0 | 3.0 |
| (14) | 2 | 6 | 6.095 | 6.02 | 5.6 | 9.0 | 9.0 | 8.64 | 10.0 | 9.64 | 10.0 | 9.64 | 0.8 | 3.8 | 3.5 | 7.36 | 7.0 | 4.0 |
| 16 | 2 | 8 | 8.115 | 8.025 | 6.4 | 10.0 | 10.0 | 9.64 | 12.0 | 11.57 | 12.0 | 11.57 | 0.8 | 4.3 | 4.0 | 8.36 | 8.0 | 4.0 |
| (18) | 2.5 | 8 | 10.115 | 10.025 | 7.2 | 11.0 | 12.0 | 11.57 | 13.0 | 12.57 | 13.0 | 12.57 | 0.8 | 4.8 | 4.5 | 9.36 | 9.0 | 5.0 |
| 20 | 2.5 | 10 | 10.115 | 10.025 | 8.0 | 12.0 | 14.0 | 13.57 | 15.0 | 14.57 | 15.0 | 14.57 | 1.0 | 5.3 | 5.0 | 10.36 | 10.0 | 5.0 |
1) Minimum depth of key engagement for set screws with nominal sizes ℓ above the dotted stepped line.
2) Minimum depth of key engagement for set screws with nominal sizes ℓ below the dotted stepped line.
3) Minimum depth of key engagement and length of dog point for set screws with nominal sizes ℓ above the dashed stepped line.
4) Minimum depth of key engagement and length of dog point for set screws with nominal sizes ℓ below the dashed stepped line.
특성표
Unit : mm| Nom Size d |
Proof torque kgf-cm [N.m] |
Recommended Seating Torque kgf-cm [N.m] |
Key Engagement |
|
Nom Size d |
Proof torque kgf-cm [N.m] |
Recommended Seating Torque kgf-cm [N.m] |
Key Engagement |
|---|---|---|---|---|---|---|---|---|
| M1.6 | 0.7 [0.07] | 0.4 [0.04] | 0.7 | 8 | 240 [23.5] | 145 [14.2] | 4 | |
| 2 | 1.5 [0.15] | 0.9 [0.09] | 0.9 | 10 | 460 [45.1] | 280 [27.5] | 5 | |
| 2.5 | 4.5 [0.44] | 2.7 [0.26] | 1.3 | 12 | 790 [77.5] | 480 [47.1] | 6 | |
| (2.6) | 4.5 [0.44] | 2.7 [0.26] | 1.3 | (14) | 900 [88.3] | 540 [53.0] | 6 | |
| 3 | 12 [1.17] | 7 [0.69] | 1.5 | 16 | 1900 [186] | 1200 [118] | 8 | |
| 4 | 28 [2.74] | 17 [1.67] | 2 | (18) | 2150 [211] | 1300 [128] | 8 | |
| 5 | 60 [5.88] | 36 [3.53] | 2.5 | 20 | 3700 [363] | 2200 [216] | 10 | |
| 6 | 100 [9.8] | 60 [5.9] | 3 |
